Wildix WS08POE Bedienungsanleitung

User ManualVersion: 01/01/2011WS08POE Switch

Administrator: Reboot Device1. Click on “Confirm” to reboot the device.Wildix WS08POE User Manual 10

Port Management: Port ConfigurationSelect the “Port No.” to configure the modes below:1. “Auto” - enable/disable Auto-Negotiation.2. “Speed” - 10M o

Port Management: Port MirroringPort Mirroring is used to mirror traffic, RX, TX or TX&RX, from Source port to Destination port for analysis.

Port Management: Bandwidth Control1. Select the “Port No.”: you can select port 1 to port 82. “TX Rate Value”: set the transmission rate of the selec

Port Management: Broadcast Storm Control 1. “Threshold” - Set the threshold from 1~63. 2. “Enable Port” - per port to define the status of broadcast p

Port Management: PoE ConfigurationRemote access and monitor the attached PD (Powered Device) status by using Enable/Disable function. ** 8-port shares

VLAN Setting: VLAN ModeThere are two VLAN modes : Port Based VLAN and Tagged VLAN.Click on “Change VLAN mode” to select the mode.**If the Port Based V

VLAN Setting: VLAN Member Setting (Port Based)You can select a port group.1. Click on the port numbers that you want to put into the selected VLAN gr

VLAN Setting: Multi to 2 SettingThis is a special design for setting the switch VLAN into “VLAN Per Port“. 1. Select “Destination Port No”. 2. Select

Per Port Counter: Counter CategoryYou can read the transmitting and receiving packet of the connecting port.Click on“Refresh” or “Clear” the data.Wil

Web Smart Switch Configure 3Administrator: Authentication Configuration 5Administrator: System IP Configuration 6Administrator: System Status 7Adm

QoS Setting: Priority ModeThere are three Priority Modes to select. 1. “First-in-First-Service” - the first receiving packet is firstly transmitted. 2

QoS Setting: Class of Service Wildix WS08POE User Manual 21

You can set QoS mode of port.TCP/UDP > TP TPS/DS > 802.1P > Physical port1. “TCP/UDP Port” – Q1 ~ Q4 options are effective for the selected p

Security: MAC Address ConfigurationSet special MAC address to activate on the selected port 1. “Select Port” – port 1~8 2. “Binding” – “Enable”: allo

Security: TCP_UDP Filter ConfigurationYou can enable or disable this function per port. If the “Function Enable” is “Enabled”, please check the follow

**Note 2: The description of Secure WAN port is shown in the bottom of this screen.3. “Protocol” – select protocols. 4. Click on “Update” to conf

Spanning Tree: STP Bridge SettingsThis setting is brought to avoid the loop network. 1. Select the “STP Mode”- select “Disable”, “STP” or “RSTP” 2. Se

Spanning Tree: STP Port Settings1. Select “Port No.”: Port 1 ~ Port 82. Select “Priority”: 0~ 2403. “RPC” = Root Path Cost: 0 = AUTO. When the loop

Trunking: Link Aggregation SettingsThere are two groups to select and max. for each group is 4 ports. Click on “Submit” to confirm and finish the sett

Backup/RecoveryFollow the instruction on the screen to update the original setting.“Backup” - Click on “Download” to confirm the setting.“Recovery” –

Web Smart Switch ConfigurePlease follow the steps to configure this Web Smart switch.Step 1: Use a twisted pair cable to connect this switch to your P

Miscellaneous: Miscellaneous Setting 1. “Output Queue Aging Time” - You can set queue aging time into different milliseconds or disable

Logout: You can click “Logout” to logout.Wildix WS08POE User Manual 31

Contacts Italy: +39 0461.1715112 [email protected] France: +33 176 747 980 [email protected] WS08POE User Manual 32

- Administrator - Port Management - VLAN Setting - Per Port Counter - QoS Setting - Security - Spanning Tree - Trunking - Backup/Recovery- Miscellane

Administrator: Authentication Configuration1. Change the user name and the password.2. Click on “Update” to confirm the new change. You can use the

Administrator: System IP Configuration1. Change the IP address: type the new IP address or select DHCP IP configuration. 2. Click on “Update” to con

Administrator: System StatusMAC address and system version are shown on the screen. 1. You can enter a new comment for this switch. 2. Click on “Upd

Administrator: Load Default Setting 1. Click on “Load” to go back to the factory default setting.**Note: Recover switch default setting excludes the I

Administrator: Firmware UpdateFollow the instruction on the screen to update the firmware. Please contact your sales agents to get the latest firmware